Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterGate Realignment in Los Angeles, CA
Gate realignment in Los Angeles typically costs between $225 and $500, depending on whether we’re correcting hinge sag, adjusting the post, or rebalancing the gate frame itself. Most realignment jobs take 1 to 2 hours on site, and we can usually schedule you within 24 hours. Call Calder Gate Repair Los Angeles at (213) 322-1415 and we’ll give you a written price before any work starts.
A gate that drags on the concrete or won’t latch isn’t just annoying, it’s a security problem. Over time, the weight of the gate pulls hinges out of square, posts lean, and the latch stops lining up with the receiver. We fix that by correcting the geometry of the gate and its mounting hardware, not by jury-rigging the latch and hoping it holds. If you’re dealing with a bigger mechanical or electrical issue, start with our Gate Repair in Los Angeles page. For the full scope of what we handle, visit our home page.
We’re Calder Gate Repair Los Angeles, the gate repair specialist inside the Relay Home Co. family, founded in 2009. Every realignment job carries our 365-Day Done Right Promise: a written price before work begins, a written guarantee on the repair, and a free second visit if the fix fails within 365 days. You’ll always know who’s coming, when they’ll arrive, and what the job costs before a single bolt is turned.
When You Need Gate Realignment
Most Los Angeles homeowners don’t realize their gate is out of alignment until it’s bad enough to see. Here are the symptoms that tell us a realignment is due:
- The gate drags or scrapes the driveway. Concrete in neighborhoods like Sherman Oaks and Silver Lake shifts over time, and if your gate is grinding across a high spot, the hinges or the post need correction, not just a lift on the hinge side.
- The latch no longer catches. When the gate settles, the latch bar sits a half-inch too low for the receiver. Adjusting the latch alone won’t fix the underlying sag, and it’ll drift again within weeks.
- The gate swings open or closed on its own. A gate that moves without you touching it means the post or hinge geometry is off. This is common on sloped driveways in hillside areas like Echo Park and Mount Washington, where gravity pulls an unbalanced gate downhill.
- Gaps appear at the top or bottom of the gate frame. If the gap between the gate and the post is wider at one corner, the frame has racked. We see this most often on wide driveway gates in the Valley, where heat and thermal expansion stress the welds.
- The gate sags on the hinge side. A visible drop of a quarter inch or more at the free end means the top hinge is pulling away under load. Ignoring it turns a $250 hinge correction into a $900 weld repair.
If the opener motor is also struggling, the misalignment may have burned the circuit board or overloaded the arm. We’ll check opener function on every realignment and tell you if the motor needs attention before it fails completely.
Our Gate Realignment Process
Here’s how a realignment works when we come to your property. You’ll know what’s happening at every step, and the price is locked in before we start.
- We measure the gate and post geometry. Our technician uses a level and tape to map how far the gate has dropped, where the hinges have moved, and whether the post itself is leaning. Then we show you the measurements and explain what they mean in plain English.
- We agree on a written price. Before any tool touches the gate, you get a written quote with the exact number. That’s the number you pay. Nothing changes at the door.
- We correct the alignment. Depending on the issue, this means re-setting hinge bolts, shimming or re-plating hinge mounts, adjusting the post, or re-hanging the gate. If we need to weld, we weld. If we need to reset the post in concrete, we do that too.
- We re-check the latch, track, and opener. Once the gate is square, we confirm the latch engages cleanly and the opener’s limit switch, the small sensor that tells the gate when to stop, is set correctly. On systems like Viking and DoorKing, a misaligned gate often forces the motor to work harder, and we want that stopped before it causes a bigger failure.
- You get a digital invoice and a written guarantee. You’ll receive an invoice by text or email that you can pay from a link. The guarantee is on paper, not a verbal promise. Both are part of The Relay Standard, the booking-to-invoice process we run on every job.
Gate Realignment Pricing in Los Angeles
Here’s what you can expect to pay for gate realignment in the Los Angeles market. These ranges include labor and standard hardware.
| Service | Typical Range |
|---|---|
| Hinge correction and re-hang (single gate) | $225 – $350 |
| Post straightening with plate or shim | $275 – $450 |
| Post replacement with concrete reset (if needed) | $450 – $800 |
| Double driveway gate realignment | $400 – $700 |
| Opener re-sync after realignment (if required) | $90 – $180 |
What drives the cost higher? Steel posts set in concrete that need to be dug out, wide driveway gates that take two people to re-hang, and openers that need re-programming after the gate moves. We’ll give you a specific number after we measure. Estimates are free, and the price we quote is the price you pay.
For a frame of reference on related work, most Gate Repair jobs in Los Angeles run between $180 and $600, and realignment sits right in the middle of that range. If the gate is beyond saving, replacement may be the smarter call, and we’ll tell you that honestly rather than sell you a realignment that won’t hold.
FAQs – Gate Realignment
How much does gate realignment cost in Los Angeles?
Gate realignment in Los Angeles typically costs between $225 and $500 for most single gates, with double driveway gates running $400 to $700. The final number depends on whether the post needs straightening or the hinges need full replacement. Call (213) 322-1415 for a free estimate, or search gate repair near me in Los Angeles, CA to book online, and we’ll give you a written price before any work starts.
Can you repair a sagging gate without replacing it?
Yes, in most cases a sagging gate can be corrected by re-hanging the gate, reinforcing the hinge mounts, or straightening the post. Replacement is only necessary when the frame itself is rusted through or the post has snapped below the concrete line. We’ll show you the measurements and explain exactly what’s recoverable.
How long does a gate realignment take?
Most realignment jobs take 1 to 2 hours on site, though post replacement with a concrete reset can take 3 to 4 hours. We’ll give you a specific time window when you book, with a live, trackable arrival time, so you’re not waiting around for a four-hour window.
Will a misaligned gate damage the opener?
Yes, a gate that drags or resists movement forces the opener motor to work harder, which shortens the life of the circuit board and gears on systems like Ghost Controls or Elite. We check the opener on every realignment call and flag any strain before it turns into a $500 motor replacement. Call (213) 322-1415 and we’ll inspect it while we’re there.
Why Los Angeles Homeowners Call Calder Gate Repair
We’re the dedicated gate repair specialist inside the Relay Home Co. family, and every job we do follows three rules: a written price before anything starts, a written guarantee on the repair, and a free second visit if the fix fails within 365 days. That’s the 365-Day Done Right Promise, and it’s not optional. It’s on every invoice we send.
Our technicians are background-checked, uniformed, and trained on the gate brands you actually own, including Viking, DoorKing, Ghost Controls, and Elite. We send a live, trackable arrival time, not a vague window. We answer the phone 24/7 with a real person. And when the job is done, you get a digital invoice you can pay from a link, with before-and-after photos attached. That’s The Relay Standard, and it’s how every Calder job runs from first call to final payment.
Written by Nico Alvarez, Owner at Calder Gate Repair Los Angeles, serving Los Angeles.