FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The Los Angeles Owner’s Guide

FAAC hinge and roller replacement in Los Angeles typically costs $190 to $420 installed depending on your gate’s size, weight, and whether we’re replacing one roller or the full hinge set. We stock FAAC-compatible hinge and roller hardware on our trucks, so most Los Angeles jobs are done the same day we arrive. You’ll usually discover the problem as a grinding noise, a gate that sags an inch or two on the latch side, or a wheel that’s stopped rolling entirely and started dragging across the concrete.

Call (213) 322-1415

Nico Alvarez has seen this hundreds of times across Los Angeles. The failure is rarely dramatic, it’s a slow wear-out that owners notice one morning when the gate doesn’t swing the way it used to.

Key Takeaways:

• Installed replacement runs $190 to $420 in Los Angeles, with the price quoted and agreed before any work starts.
• We carry FAAC-compatible hinges and rollers on the truck, so most repairs finish same-day.
• Every replacement is covered by our 365-Day Done Right Promise in writing.
• Ignoring a worn roller turns a $220 part swap into a $1,400 motor replacement faster than you’d think.

Which FAAC Models This Applies To

We service the full FAAC line across Los Angeles, including the 415, 400, C720, C721, S418, S450H, and 844 series operators with their matching gate hardware. FAAC hinges and rollers vary by gate weight class and swing direction, so the first thing we do on-site is confirm your model number and measure the existing hardware before pulling a replacement.

Here’s the compatibility gotcha most Los Angeles owners run into: FAAC roller brackets are sized to the gate leaf, not the opener. A C720 on a 14-foot iron gate uses a different roller diameter and hinge offset than the same opener on a 9-foot tubular steel gate. If you order by opener model alone, you’ll get the wrong part about a third of the time.

OEM FAAC hardware is well made, but the aftermarket equivalents we install (from brands like Linear-compatible brackets and US-market steel rollers) often match or exceed OEM spec for $30 to $60 less per assembly. For a gate past year eight in Los Angeles sun and coastal air, we typically recommend aftermarket stainless-accented rollers over the original zinc-plated units, which pit faster than most owners expect.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate looks drunk at the latch end. A visible sag of more than half an inch at the unlatching side almost always means a hinge pin or roller bearing has worn past spec.
• You hear a crunch when the gate opens, not a hum. The roller wheel seizes, the gate drags it sideways across the track or concrete, and the crunch is the sound of metal grinding on metal.
• The gate shudders or jerks as it moves. A worn roller creates intermittent resistance, and your FAAC operator responds by pulsing power, which reads as a jerk at the leaf.
• The close cycle stops short or reverses. As the droop worsens, the obstruction sensor reads the drag as a blockage. The gate isn’t broken, it’s just fighting a dead roller.
• You can shift the gate leaf more than an inch by hand when it’s closed. That slop is a hinge pin down to half its original diameter, and it only gets worse from here.

Replacement Cost & What’s Included

Most FAAC hinge and roller replacements in Los Angeles run $190 to $420 installed. A basic single-roller swap on a residential single-swing gate starts around $190. Replacing both hinges and both rollers on a heavy double-swing iron gate lands around $420, sometimes a bit more if we need to weld a fresh bracket plate.

You’ll get the full number in writing before anything comes off the gate. The quote includes the parts, the labor, the adjustment of the gate so it swings and latches clean, and the trip charge. If the gate is badly misaligned from months of dragging, we’ll tell you upfront whether the fix is a simple hardware swap or whether the post needs reshimming, because that second option changes the price meaningfully.

Every FAAC hinge and roller replacement we do in Los Angeles is covered by the 365-Day Done Right Promise: if the repair fails within 365 days, Calder Gate Repair returns at no charge. Not pro-rated, not “under certain conditions.” We come back.

DIY or Call Us?

Some of this you can check yourself. Open the gate manually and watch the roller. If the wheel isn’t turning, or turns with a wobble, that’s your answer. You can also grab the gate leaf at chest height and lift. More than half an inch of vertical movement means the hinge pins are shot and you should call us at (213) 322-1415.

What we don’t recommend is swapping FAAC hinge hardware yourself. A gate leaf under tension stores a lot of energy, and if the leaf shifts while the hinge bolts are out, it can crush a hand or pin someone against the post. This is one repair where the $220 you’ll spend on us is cheaper than what an urgent care visit costs, and it actually gets the gate fixed. If the gate has sagged enough that the opener is fighting it, leave the opener powered off until the hardware is replaced, don’t ask the motor to do a job the rollers gave up on.

FAQs

Call Calder Gate Repair Los Angeles

If your FAAC gate is dragging, crunching, or sagging, call us at (213) 322-1415. We’ll give you a straight answer on the phone, a written price before any work starts, and a technician with a live arrival time you can track. We stock hinges and rollers for FAAC, LiftMaster, Mighty Mule, and Ghost Controls, and we fix the gate right the first time, or we come back free under the 365-Day Done Right Promise. Nico’s approach: “Tell me what it’s doing wrong and I’ll tell you what it actually costs to fix it, before I pick up a tool.”

Written by Nico Alvarez, Owner, Calder Gate Repair Los Angeles at Calder Gate Repair Los Angeles, serving Los Angeles and nearby areas.